MIPROCRETE-HF Trowel PU Concrete

About MIPROCRETE-HF Trowel PU Concrete

MIPROCRETE-HF Trowel Pu Concrete is a four-component polyurethane screed specifically designed for industrial applications. This trowel-applied system can be installed at thicknesses of 69 mm and features a matt, anti-skid finish. It combines outstanding durability, high performance, and excellent aesthetics, making it an ideal choice for heavy-duty industrial flooring where safety, longevity, and visual appeal are essential.

DESCRIPTION
A 4 component polyurethane trowel applied screed in thickness from 6-9mm for industrial application and repairing system in matt anti-skid finish offering versatility in performance, aesthetics and economics.

USES

ADVANTAGES

COLOURS
MIPROCRETE HF Trowel Pu Concrete floor system is functionally formulated to withstand severe chemical, mechanical, and thermal damages. As a direct result slight yellowing of the floor surface exposed to UV may occur especially in light colors without affecting its functionality.

CHEMICAL RESISTANCE

MIPRO-CRETE HF Trowel Pu Concrete will resist spillages of

Resistance is maintained in many cases to 130 ^oC, which should be regarded as the maximum service temperature. Detailed test data available upon request.

APPLICATION PROCEDURE

Surface Requirement & Preparation
Substrate will normally be concrete or polymer modified screeds with minimum compressive strength 25N1mm² and pull-off strength 1.5N/mm². If substrate moisture exceeds 4%, use water base epoxy primer and allow it to dry.

For floor in need of repair above 10mm use solvent free epoxy primer. Preferably vacuum shot blast the surface with non-impact method. Concrete surface planer, grit blasting and surface grinding or other mechanical means until a profile is evident can be satisfactory. Substrate must be clean, free from dust, oil, water, paint residues, loose constituents or any contaminants.

Prepare grooves, 8mm wide X 8mm deep, at all edges, bay joints columns, doorways, and drains for anchoring purpose.

IMPORTANT:
Old floor needs thorough inspection for its integrity providing an ideal substrate for maximum adhesion. If has to be free from all contaminants. Grooves 8mm wide and 8mm deep have to be created diagonally into the floor every 1m² area of the floor to facilitate mechanical bonding.

PRIMING
All MIPRO-CRETE-HF Trowel Pu Concrete floor should be applied onto cured water base epoxy primer, which has been broadcasted with silica sand.

MIXING
Add part A, Polyol, to a clean mixing drum. Add Part B, isocynanate, to the drum and mix for 15 second until uniform using a helical spinner. Add Part -C pigmented Powder and further mix for 2 minutes to achieve a fully homogenized consistent mortar. Remove residue of previous mix from the sides of the drum and discard before the next pack.

APPLICATION
Apply MIPRO-CRETE HF Trowel Pu Concrete WITHIN ITS POT LIFE.
o thickness 6-10mm and consolidate with steel trowel to the correct depth. Use short nap roller dipped in xylene and roll lightly on the surface to bring up the resin.

PACKAGING
30 kg. packs, consisting of Base A, Hardener B & Filler C

STORAGE

All parts of MIPRO-CRETE-HF Trowel Pu Concrete should be stored properly in origin (un-opened) packaging in dry conditions at 10-32 ^oC.

SHELF LIFE: Will be 6 months minimum. Exaggerated temperature humidity ranges can adversely affect shelf life.

HEALTH & SAFETY
Some of the components of this product may be hazardous during mixing & application. Always use with suitable protective gears. Close container tightly after use. Keep out of reach of children.

FURTHER INFORMATION
With a wealth of technical & practical experience built u over many years in our pursuit of excellence in flooring and concrete technology, make us your partner today!

TECHNICAL DATA

Density, kg/mm/m2	2.1
Compressive Strength	62 N/mm2
Tensile Strength	7 N/mm2
Flexural Strength	15 N/mm2
Bond Strength	Concrete Failure
Thermal Conductivity	Very Low
Taber abrasion resistance	1110 mg loss
Impact Resistant	<0.5 (BRE Screed tester) ml
Mixing Ratio	As mention on packing
Pot life	20min at 25 oC
Pack Size (A+B+C)	30 kgs
Storage & Shelf Life	Unopened in cool dry condition 10o -25o C/ 6 months
Temp. Resistance	130o C @ 9mm Thickness
Estimated coverage 6mm thickness	2.5 M2 /Pack size of 30kgs
NOTE: Coverage figure given is theoretical. Due to wastage & roughness of surface & method of application, the actual coverage may be reduced.

Technical Details

Durable Floor Solutions for Every Requirement

MIPROCRETE-HF Trowel PU Concrete is created to withstand heavy wear and corrosion, making it ideal for high-traffic industrial settings. With size customization available, clients receive tailored solutions for their flooring needs. The plain surface treatment ensures easy maintenance and a clean appearance. Provided by an experienced Indian manufacturer and exporter, MIPROCRETE-HF sets a benchmark for quality and reliability.


Versatile Applications Across Industries

From manufacturing plants and warehouses to commercial facilities, MIPROCRETE-HF adapts to a wide variety of flooring applications. The product's strong PU base ensures longevity and resilience, while its adaptability to different size requirements streamlines installation in any setting. Comprehensive after-sales support from the supplier enhances the product's value throughout its lifecycle.